Tool Adapter for 850/960/S70/V70/S90 Serpentine Belt Tensioner
Thread Starter
|
Administrator
Joined: Mar 2009
Posts: 15,736
Likes: 36
From: Albuquerque, NM
Tool Adapter for 850/960/S70/V70/S90 Serpentine Belt Tensioner
Serpentine belt tensioner adapter and holder, $9.50 (each additional kit $6.50). I have more than 10 available.
Fits the tensioner for the following vehicles:
- 850 = '94 - '97
- 960, S/V90's = '95 - '98 (maybe earlier models as well).
- S/V70's = '98
TOOL KIT:
TENSIONER:
I kinda got tired to fumbling with my plumbing adapter when taking my serpentine belt tensioner loose, dropping it down into the motor, slipping pipe wrench, etc.. So I decided to get something easy for me and didn't want to pay $30 plus shipping for the proper tool.
Well, the size was not standard so it was a little challenging. Long story short, it was a little expensive to get just one made so I thought if I had several of them made I could share them (and a little of the cost) with others. So here you have it, a small kit to take your belt tensioner loose and pin it retracted. A few of them cost me way to much but hopefully a few of you guys can use something small for your box (or 2) that you can toss in your pocket if you'd like.
It's solid steel so it should last forever. If you need one, I'll give you a 100 year warranty. The screw fits perfectly as well, leaves a little out so it's easy to remove with your fingers.
Part plus shipping will be $9.00 (A lot cheaper than $30 plus shipping). That will cover the parts, package, shipping, and give me couple of $$$ to offset my bulk cost. If you want one or two of them (or more) please pm me. Each additional set will be $6.50. Please purchase a few.
Solid steel stud that will fit in the serpentine tersioner hole and leave enough out to put a wrench on. Once set in, it will not fall out. It's a good fit.
Fits the tensioner for the following vehicles:
- 850 = '94 - '97
- 960, S/V90's = '95 - '98 (maybe earlier models as well).
- S/V70's = '98
TOOL KIT:
TENSIONER:
I kinda got tired to fumbling with my plumbing adapter when taking my serpentine belt tensioner loose, dropping it down into the motor, slipping pipe wrench, etc.. So I decided to get something easy for me and didn't want to pay $30 plus shipping for the proper tool.
Well, the size was not standard so it was a little challenging. Long story short, it was a little expensive to get just one made so I thought if I had several of them made I could share them (and a little of the cost) with others. So here you have it, a small kit to take your belt tensioner loose and pin it retracted. A few of them cost me way to much but hopefully a few of you guys can use something small for your box (or 2) that you can toss in your pocket if you'd like.
It's solid steel so it should last forever. If you need one, I'll give you a 100 year warranty. The screw fits perfectly as well, leaves a little out so it's easy to remove with your fingers.
Part plus shipping will be $9.00 (A lot cheaper than $30 plus shipping). That will cover the parts, package, shipping, and give me couple of $$$ to offset my bulk cost. If you want one or two of them (or more) please pm me. Each additional set will be $6.50. Please purchase a few.
Solid steel stud that will fit in the serpentine tersioner hole and leave enough out to put a wrench on. Once set in, it will not fall out. It's a good fit.
Last edited by rspi; Feb 20, 2014 at 10:45 PM. Reason: pic, update price
Junior Member
Joined: Mar 2011
Posts: 15
Likes: 0
From: Orange Park, FL
Just got mine yesterday, and I must say every 850 owner needs one of these. It was even coated bright yellow, so I'll be sure to never lose it! If you do any wrenching on your car, you owe it to yourself to get this tool.
Junior Member
Joined: Apr 2011
Posts: 1
Likes: 0
Senior Member
Joined: Aug 2015
Posts: 104
Likes: 0
Serpentine belt tensioner adapter and holder, $9.50 (each additional kit $6.50). I have more than 10 available.
Fits the tensioner for the following vehicles:
- 850 = '94 - '97
- 960, S/V90's = '95 - '98 (maybe earlier models as well).
- S/V70's = '98
TOOL KIT:
TENSIONER:
I kinda got tired to fumbling with my plumbing adapter when taking my serpentine belt tensioner loose, dropping it down into the motor, slipping pipe wrench, etc.. So I decided to get something easy for me and didn't want to pay $30 plus shipping for the proper tool.
Well, the size was not standard so it was a little challenging. Long story short, it was a little expensive to get just one made so I thought if I had several of them made I could share them (and a little of the cost) with others. So here you have it, a small kit to take your belt tensioner loose and pin it retracted. A few of them cost me way to much but hopefully a few of you guys can use something small for your box (or 2) that you can toss in your pocket if you'd like.
It's solid steel so it should last forever. If you need one, I'll give you a 100 year warranty. The screw fits perfectly as well, leaves a little out so it's easy to remove with your fingers.
Part plus shipping will be $9.00 (A lot cheaper than $30 plus shipping). That will cover the parts, package, shipping, and give me couple of $$$ to offset my bulk cost. If you want one or two of them (or more) please pm me. Each additional set will be $6.50. Please purchase a few.
Solid steel stud that will fit in the serpentine tersioner hole and leave enough out to put a wrench on. Once set in, it will not fall out. It's a good fit.
Fits the tensioner for the following vehicles:
- 850 = '94 - '97
- 960, S/V90's = '95 - '98 (maybe earlier models as well).
- S/V70's = '98
TOOL KIT:
TENSIONER:
I kinda got tired to fumbling with my plumbing adapter when taking my serpentine belt tensioner loose, dropping it down into the motor, slipping pipe wrench, etc.. So I decided to get something easy for me and didn't want to pay $30 plus shipping for the proper tool.
Well, the size was not standard so it was a little challenging. Long story short, it was a little expensive to get just one made so I thought if I had several of them made I could share them (and a little of the cost) with others. So here you have it, a small kit to take your belt tensioner loose and pin it retracted. A few of them cost me way to much but hopefully a few of you guys can use something small for your box (or 2) that you can toss in your pocket if you'd like.
It's solid steel so it should last forever. If you need one, I'll give you a 100 year warranty. The screw fits perfectly as well, leaves a little out so it's easy to remove with your fingers.
Part plus shipping will be $9.00 (A lot cheaper than $30 plus shipping). That will cover the parts, package, shipping, and give me couple of $$$ to offset my bulk cost. If you want one or two of them (or more) please pm me. Each additional set will be $6.50. Please purchase a few.
Solid steel stud that will fit in the serpentine tersioner hole and leave enough out to put a wrench on. Once set in, it will not fall out. It's a good fit.
Hello Robert, I have sent you an order via PM, please check your message box. Thank you!